TM
D e s c r ip t io n
The MD-CC1 0 0 -0 0 0 Parameter Setup Cable eliminates
the need for the user to wire communications to the IMS
product. Included in this cable is built-in logic level shifting
circuitry to accommodate the 3 .3 v ports on some PCs.
in t e l l ig e n t m o t io n s y s t e m s , in c .
Excellence in MotionTM
This cable plugs in easily to connect a standard DB-2 5
PC Parallel/ SPI port to the 1 0 pin header.
MD-CC100-000
Parameter Setup Cable
S P I P in A s s ig n m e n t s
10 Pin Header
Pin #
1
2
Pin Name
N/C
Description
No Connect
No Connect
N/C
3
N/C
No Connect
4
CS
Chip Select
5
6
7
8
GND
+5VDC
MOSI
CLK
Communications Ground
+5VDC Output (See Warning Below)
Master Out – Slave In
Clock
9
N/C
No Connect
10
MISO
Master In – Slave Out
WARNING! The +5VDC output is used for the setup cable
ONLY! This output is not designed to power external devices!
370 N. MAIN ST., PO BOX 457, MARLBOROUGH, CT 06447
PH: (860) 295-6102, FAX: (860) 295-6107
WARNING! DO NOT connect or disconnect the MD-CC100-000
Parameter Setup Cable while power is applied!
S P I In t e r f a c e
P a r a m e t e r S e t u p C a b l e U s a g e
The MD-CC1 0 0 -0 0 0 Parameter Setup Cable is designed to be
used with the following IMS products:
PIN 4 - CS
GND - PIN 5
MOSI - PIN 7
PIN 6 - +5VDC OUT
PIN 8 - CLOCK
MDrive1 4 *
PIN 10 - MISO
MDrive1 7 Microstepping* and Speed Control Versions
MDrive2 3 Microstepping* and Speed Control Versions
MDrive3 4 Microstepping and Speed Control Versions
USC-4 8 -2 Universal Speed Control
DB-25 Standard
PC Parallel/SPI Port
10 Pin Header
P2
2
3
4
19
15
Ground
*
The MDrive1 4 , MDrive1 7 C and MDrive2 3 C are equipped with C Connector and
require an Adapter Cable to interface with the MD-CC1 0 0 -0 0 0 . The optional
Prototype Development Cable is also recommended for these products.
For More Information:
See each product’s complete manual
on the IMS Product CD or at www.ims home.com
D e t a il s
To Customer PC
Parallel/SPI Port
Pin 1
To 10 Pin Header
Pin 2 - SPI Clock
Pin 3 - MOSI
Red Wire
# 1 Pin
Pin 15 - MISO
Pin 4 - SPI Chip Select
Pins 18-25
Ground
Cable Length
6 Feet (1.8 M)
Standard DB-25
Parallel/SPI Connector
Revision 102104
Copyright © 2003–2004 Intelligent Motion Systems, Inc.
|
Intellinet Network Solutions Security Camera 550000 User Manual
JBL Home Theater System 201 User Manual
Jet Tools Lathe JML 1014 User Manual
JVC CD Player KD G737 User Manual
JVC Portable CD Player 0910TMMMDWMTS User Manual
JVC VCR HR J271MS User Manual
Kenmore Vacuum Cleaner 11635622 User Manual
Kenwood GPS Receiver DDX7036BT User Manual
KitchenAid Ice Maker KUIS18NNTB2 User Manual
Kodak Film Camera KB 22 User Manual