COMPONENT WOOFER INSTALLATION INSTRUCTION MANUAL
COMPONENT WIRING DIAGRAM:
EXTERNAL 2-WAY
CROSSOVER
MOUNTING LOCATION
Carefully select a suitable mounting location for the speaker/tweeter. Be sure to check
behind the mounting location selected for adequate space for speaker/tweeter depth.
Use the included template if needed
MOUNTING HOLE
SPEAKER : Using a sharp knife or razor, cut the panel using the outline from the template as a guide. Also,
drill holes for the mounting screws if installing on metal panels.
SIGNAL SOURCE UNIT
RADIO OR AMPLIFIER
INSTALLATION
SPEAKER : Place ABS grill on top of speaker and secure assembly using the self tapping
screw provided. *NOTE : If not using the included grill, grill mount does not have to be installed.
TWEETER : Screw the angle mounting to the location selected or use the double sided
tape provided to stick the flush mounting to the location selected.
WIRING
SPEAKER: Carefully route the supplied wire to the speaker, ensuring that it does not pass over any sharp
metal edges that will damage the signal path. Connect the terminal ends of the wires to the speakers,
watching that the left/right and positive/negative connections are made correctly to the appropriate
outputs of the radio or amplifier.
TWEETER : Feed the wires from the tweeter through the flush/angle mounting opening
and connect these wires to the line wires coming from the included outboard crossover tweeter
terminals. Push the tweeter into the flush/angle mounting until the tweeter sits nicely into the mounting.
SPECIFICATIONS :
MODEL: IFC-525
*NOTE : When installing tweeter with flush mount kit, a hot glue gun is sometimes necessary to secure
the tweeter's flush mount housing.
MODEL: IFC-650
5.25" 2-Way High Definition
Component System
6.5" 2-Way High Definition
Component System
5.25" Injection PP Mica Cone
Rubber Surround and
1" Titanium Dome Tweeter
with Neodymium Magnet
6.5" Injection PP Mica Cone
Rubber Surround and
1" Titanium Dome Tweeter
with Neodymium Magnet
INSTALLATION PROCEDURE :
Mounting Holes
Peak Power Handling
: 300Watts
Peak Power Handling
: 350Watts
Continuous Power (RMS) : 150 Watts
Continuous Power (RMS) : 175 Watts
Impedance
: 4 Ohm
Impedance
: 4 Ohm
Magnet Weight
Sensitivity (1W/m)
Freq. Response
Woofer Voice Coil Dia.
Fo (Freq. Resp.)
Qts (Total Q)
Vas
: 10 Oz
Magnet Weight
Sensitivity (1W/m)
Freq. Response
Woofer Voice Coil Dia.
Fo (Freq. Resp.)
Qts (Total Q)
Vas
: 13 Oz
: 91 dB
: 91 dB
Angle Mounting
: 50Hz - 25kHz
: 1" (25mm) ASV
: 92.06 Hz
: 0.82
: 40Hz - 25kHz
: 1" (25mm) ASV
: 53.1 Hz
: 0.61
Speaker Unit
Screw
Grill
Mounting Screws
: 4.1 Lt
: 12.42 Lt
: 12dB/Oct
Tweeter
Crossover
: 12dB/Oct
Crossover
Speaker
Double sided
Tape
Flush Mounting
Interfire Audio Inc.
Santa Fe Springs, CA, www.inter fireaudio.com
Tweeter
|
Indesit Washer IWB6065 User Manual
IOGear Network Card GDIP201 User Manual
iOptron Telescope 8600 User Manual
Jackson Dishwasher JV 24 B BF User Manual
JBL Professional Car Speaker Control 28 User Manual
JVC Camcorder 0503 FO ID VP User Manual
JVC Car Speaker CS HX7 User Manual
JVC Headphones HAFR50P User Manual
Kenwood MP3 Docking Station KDC U549BT User Manual
Kompernass Heat Gun PHLG 2000 SE User Manual