KitchenAid Blender 5KHB3583 User Manual

5KHB3583  
 
HaND BlENDEr SaFETY  
IMPorTaNT SaFEgUarDS  
When using electrical appliances, basic safety precautions should always  
be followed, including the following:  
1. Read all instructions.  
2. To protect against risk of electrical shock, do not put motor body of Hand Blender,  
battery, charger, charger’s cord or plug in water or other liquid.  
3. This appliance is not intended for use by persons (including children) with reduced  
physical sensory or mental capabilities, or lack of experience and knowledge, unless  
they have been given supervision or instruction concerning use of the appliance by  
a person responsible for their safety.  
4. Children should be supervised to ensure that they do not play with the appliance.  
5. Avoid contact with moving parts.  
6. Do not operate any appliance or charger with a damaged cord, or plug, or after the  
appliance or charger malfunctions, or is dropped, or damaged in any manner. Return  
appliance or charger to the nearest Authorized Service Facility for examination, repair,  
or electrical or mechanical adjustment.  
7. The use of attachments not recommended or sold by KitchenAid may cause fire,  
electric shock, or injury.  
8. Do not let power cord on charger hang over edge of table or counter. Excess cord  
may be wrapped on the underside of the charger.  
9. Do not let power cord on charger contact hot surfaces, including the stove.  
10. When mixing liquids, especially hot liquids, use a tall container, or make small quantities  
at a time to reduce spillage.  
11. Keep hands and utensils out of the container while blending to prevent the possiblity  
of severe injury to persons, or damage to the unit. A scraper may be used, but must  
be used only when the unit is not running.  
12. Blades are sharp. Handle carefully.  
13. Always remove the battery from the Hand Blender if it is left unattended and before  
assembling, disassembling or cleaning.  
14. This product is designed for household use only.  
DownSloaad frvomEWwTw.HSomEaSnuEals.cIoNm. SAllTMarnuUalsCSeTarcIhoAndNDoSwnload.  
6
Hand Blender Safety  
electrical requirements  
Battery Voltage: 12 V Lithium-Ion (Li-ion) / 1.5 Ah / 16 Wh  
Battery Model No.: 5KCL12IBOB  
Charger  
Input : 18 V / 660 mA  
Output : 12 V / 550 mA  
Charger Model No.: 5KCL12CSOB  
Charger Adapter  
Input : 220-240 V / 50/60 Hz / 18 W  
Output : 18 V / 660 mA  
Charger Adapter Model No.: W10533411  
electrical equipment waste disposal  
This appliance is marked according to the  
European directive 2002/96/EC on Waste  
Electrical and Electronic Equipment (WEEE).  
By ensuring this product is disposed  
of correctly, you will help avoid potential  
negative consequences for the environment  
and human health, which could otherwise  
be caused by inappropriate waste handling  
of this product.  
treated as household waste. Instead it shall  
be handed over to the applicable collection  
point for the recycling of electrical and  
electronic equipment.  
Disposal must be carried out in accordance  
with local environmental regulations  
for waste disposal.  
For more detailed information about  
treatment, recovery, and recycling of this  
product, please contact your local city office,  
your household waste disposal service, or  
the shop where you purchased the product.  
The symbol on the product, or on the  
documents acompanying the product,  
indicates that this appliance may not be  
disposing of Kitchenaid lithium-Ion (li-Ion) battery  
Always dispose of your battery according to  
local regulations. Contact a recycling agency  
in your area for recycling locations.  
Even discharged batteries contain some  
energy. Before disposing, use electrical tape  
to cover the terminals to prevent the battery  
from shorting, which could cause a fire or  
explosion.  
 
7
ParTS aND FEaTUrES  
Parts and features  
Battery location  
Bell guard  
Pan guard  
Front of  
motor body  
Back of motor body  
Battery release  
lever /  
Hanging loop  
Unlock button  
Speed control  
buttons  
lED display  
speed selection  
indicator  
Pulse button  
grip  
lED display  
battery life  
indicator  
Battery  
lED charge  
indicator/ lid  
release  
20 cm (8") Stainless  
steel blending arm  
with S-blade  
Charger base  
8
 
oPEraTINg THE HaND BlENDEr  
Before first use: charging the battery  
Plug in the charger.  
Push the lid release button to open  
1
3
2
4
the lid.  
Slide the battery into the charger,  
aligning the flat side of the battery to the  
flat side of the port, and push down to  
click into place.  
The LED indicator will begin to flash  
slowly and continuously as it charges.  
When the battery is fully charged, the  
LED will display a continuous light.  
NoTE: If the charger quickly flashes three  
times after inserting the battery, there is a  
battery error. Check that the battery is placed  
properly in the charger. If the light continues  
to flash rapidly, the battery may be extremely  
cold, hot, wet or damaged. Allow the battery  
to cool down, warm up or dry out, then  
reinsert. If the problem persists, see the  
“Service and Warranty” section.  
Charge the battery after each use, when  
the battery indicator lights show less  
than 25% battery life remaining (only  
one light displays on the LED battery  
life indicator), or when the battery is  
completely drained.  
5
NoTE: Batteries do not develop a “memory”  
when charged after only a partial discharge. It  
is not necessary to run down the battery  
before placing it on the charger.  
9
 
oPEraTINg THE HaND BlENDEr  
assembling the Hand Blender  
Before First Use  
Before using the Hand Blender for the  
first time, wipe the motor body, the  
blending arm with blade and the guards  
with a clean, damp cloth to remove any  
dirt or dust. Mild dish soap may be used.  
Do not use abrasive cleansers. Dry  
thoroughly with a soft cloth. See “Care  
and Cleaning” section for more information.  
Insert blending arm into motor body  
and twist until it clicks to lock in place.  
Remove the bell guard from the blade.  
1
2
Port  
Mounting  
grips  
If using a pan guard, place it on a flat  
surface and position with mounting clips  
between the ports of the blade.  
Snap pan guard into place with an even,  
downward motion.  
3
4
NoTE: Use the bell  
guard to avoid damage to  
blade when Hand Blender  
is not in use.  
Bell guard  
Use the pan guard to  
avoid damage to cookware  
while using Hand Blender.  
Slide the charged battery into the top  
5
Pan guard  
of the Hand Blender motor body. Make  
sure it latches securely.  
10  
 
oPEraTINg THE HaND BlENDEr  
Using the lED display panel  
IMPorTaNT: The unlock button must be pressed before the Hand Blender will operate.  
Battery life  
indicator  
lED display  
Unlock  
button  
When operating the controls on the  
Hand Blender, always make sure the  
LED display is facing toward you. Grip  
the handle with your thumb on the  
back of the unit, and your fingers on the  
controls in front, as shown.  
The bottom bar on the LED display  
panel is the battery life indicator. Hold  
the Hand Blender so that you can see  
the LED display light up when you  
press the UNLOCK button with your  
index finger.  
1
2
Pulse button  
Speed control  
buttons  
Speed selection  
indicator  
The top bar on the LED display panel is  
After selecting desired speed, press  
the PULSE button to begin blending.  
See “Using the blending arm” section  
for more information.  
3
4
the speed selection indicator. To adjust  
speeds, operate the arrow buttons  
with your index finger, while viewing  
the speed indicator on the LED display.  
When the LED faces you, the right  
button will increase the speed and the  
left button will decrease the speed.  
NoTE: The Hand Blender will automatically power down after 60 seconds of not operating  
or being manually unlocked.  
11  
 
oPEraTINg THE HaND BlENDEr  
Using the blending arm  
NoTE: Your Hand Blender is ideal to use for blending, crushing, or puréeing. It is best used for  
soups, cooked vegetables, sauces, baby food, smoothies, milk shakes, frosting, or crushed ice.  
Unlock  
button  
Speed control  
buttons  
lED display  
Speed selection  
indicator  
Press the UNLOCK button. LED display  
will light up when unit is ready.  
Use the arrow buttons to adjust the  
speed, using the LED display as a guide.  
1
2
Pulse button  
Seam  
Insert Hand Blender into mixture. Then  
press the PULSE button to activate.  
NoTE: Do not immerse hand blender  
in liquids deeper than the seam of the  
attachment. Do not immerse motor body  
into liquids or other mixtures.  
3
After blending is complete, release the  
pulse button; then remove Hand Blender  
from mixture.  
Remove the battery by placing your  
4
5
finger on the battery release lever and  
pulling the lever away from the motor  
body. The battery will release from  
the top of the unit.  
TIP: To avoid splashing, insert the Hand  
Blender into the mixture before pressing  
the pulse button, and release the pulse  
button before pulling the Hand Blender  
out of the mixture.  
IMPorTaNT: Always wait to insert  
battery into Hand Blender until accessories  
are attached. After using, always remove  
battery before disassembling Hand Blender.  
12  
 
TIPS For grEaT rESUlTS  
Techniques for better blending and crushing  
Wrist  
movement  
Drawing up  
For better blending: Rest the Hand Blender on the bottom of the container momentarily, then  
hold at an angle and using a light circular motion, slowly draw it upwards against the side of the  
container. Allow your wrist motion and the weight of the Hand Blender to do the work. As you  
draw up the Hand Blender, you will notice the ingredients from the bottom of the container rising  
up. When the ingredients are no longer rising from the bottom, return the Hand Blender to the  
bottom of the container and repeat until mixture is at the desired consistency.  
TIP: To prevent overflow, allow room  
in the container for the mixture to rise  
when blending.  
For better crushing: Insert Hand Blender  
with blending arm attached into the  
container. For hard, frozen fruits or ice,  
add a small amount of liquid until the  
S-blade is submerged. Remember to stop  
the Hand Blender before removing it from  
the container to avoid splashing.  
operating tips  
• Do not let the Hand Blender sit in a hot  
• When blending in a saucepan on  
a cooktop, remove the pan from  
the heating element to protect the  
Hand Blender from overheating.  
pan on the cooktop when not in use.  
• The Hand Blender is equipped with  
thermal protection from high operating  
temperatures. Should the Hand Blender  
suddenly stop during use, press the  
UNLOCK button once, then press  
the PULSE button. If the unit does not  
operate, but shows information on the  
battery indicator bar, allow 10 minutes  
to automatically reset. If the unit does  
not display information on the battery  
indicator bar, charge the battery. If the  
battery is already fully charged, and the  
unit fails to operate, see the “Service  
and Warranty” section.  
• Cut solid foods into small pieces  
for easier blending.  
• Do not use Hand Blender to process  
coffee beans or hard spices such as  
nutmeg. Processing these foods may  
damage the blades.  
13  
 
CarE aND ClEaNINg  
Cleaning the Hand Blender  
Remove blending arm (see “Operating  
the Hand Blender” section).  
Wash blending arm and guards in the  
top rack of the dishwasher or by hand in  
hot, soapy water. Dry with a soft cloth.  
1
2
NoTE: Always remove the battery from  
the Hand Blender if it is left unattended  
and before assembling, disassembling  
or cleaning.  
Do not immerse motor body in water.  
Wipe the motor body with a damp  
3
cloth. Use mild dish soap. Do not use  
abrasive cleansers.  
14  
 
SErvICE aND WarraNTY  
Kitchenaid Hand Blender warranty  
Length of  
Warranty:  
KitchenAid Will Pay For:  
KitchenAid Will Not  
Pay For:  
Europe, Middle  
The replacement parts  
A. Repairs when Hand Blender  
is used for operations other  
than normal household  
food preparation.  
B. Damage resulting from  
accident, alterations,  
misuse, abuse, or  
East and Africa: and repair labor costs to  
correct defects in materials  
For Model  
5KHB3583:  
Three years Full  
Warranty from  
date of purchase.  
or workmanship. Service  
must be provided by an  
Authorized KitchenAid  
Service Center.  
installation/operation  
not in accordance with  
local electrical codes.  
KITCHENAID DOES NOT ASSUME ANY RESPONSIBILITY FOR INDIRECT DAMAGES.  
Customer service  
In U.K. and Ireland:  
For any questions, or to find the nearest KitchenAid Authorized Service Center, please find  
our contact details below.  
NoTE: All service should be handled locally by an Authorized KitchenAid Service Center.  
Contact number for U.K. and Northern Ireland:  
Tollfree number 0800 988 1266 (calls from mobile phones are charged standard  
network rate)  
Contact number for Ireland:  
Tollfree number +44 (0) 20 8616 5148  
E-mail contact for U.K. and Ireland:  
Address for U.K. and Ireland:  
KitchenAid Europa, Inc.  
PO BOX 19  
B-2018 ANTWERP 11  
BELGIUM  
In other countries:  
For all product related questions and after sales matters, please contact your dealer  
to obtain the name of the nearest Authorized KitchenAid Service/Customer Center.  
© 2012. All rights reserved.  
Specifications subject to change without notice.  
15  
 
© 2013. All rights reserved.  
Specifications subject to change without notice.  
W10532509B  
01/13  
 

Infinity Vacuum Cleaner NV28 User Manual
Invacare Wheelchair 1080556 User Manual
JOBO Camcorder Giga 3+ User Manual
JVC CD Player CH X1000 X400 User Manual
JVC Home Theater System RX E12B User Manual
Kenmore Refrigerator 7957109 User Manual
KitchenAid Dishwasher KUDC03ITBL2 User Manual
KitchenAid Slow Cooker 9763141A User Manual
Kramer Electronics Home Theater System VP 411DS User Manual
Kramer Electronics Network Cables VP 81 K User Manual