KitchenAid Clothes Dryer KEYS700JKEYS700L User Manual

®
Electric Dryer  
PRODUCT MODEL NUMBERS  
OVERALL DIMENSIONS  
KEYS700J  
KEYS700L  
KEYS710L  
KEYS750J  
KEYS750L  
KEYS850J  
KEYS850L  
KEYS855J  
Electrical: A four-wire or three-wire, single  
phase, 120/240-volt, 60-Hz, AC-only, electrical  
supply (or 120/208-volt electrical supply, if  
specified on the serial/rating plate) is required on a  
separate 30-ampere circuit, fused on both sides of  
the line. Use 10 gauge solid copper wire. A time-  
delay fuse or circuit breaker is recommended.  
Exhaust venting: Exhaust your dryer to the  
outside. Four-inch diameter vent is required. Rigid  
or flexible metal exhaust vent must be used. Do  
Not use plastic or metal foil vent. Exhaust outlet  
hood must be at least 12 inches from the ground  
or any object that may be in the path of the  
exhaust.  
RECESSED AREA AND CLOSET INSTALLATION  
"
"
"
1. Small Opening Side-Swing Door  
2. Large Opening Side-Swing Door  
3. Wide Opening Side-Swing Door  
4. Wide Opening Hamper Door  
"
"
"
51  
"
2
29"  
(73.66 cm)  
"
27  
"
"
4
"
(70.5 cm) (14 cm)  
1
3
2
For closet installation with a door, minimum  
ventilation openings in the top and bottom of  
the door are required. Louvered doors with  
equivalent air openings are acceptable.  
1. Recessed area  
2. Side view - closet or confined area  
3. Closet door with vents  
EXHAUST VENTING  
1. Select the route that will provide the straightest and most direct path outdoors.  
Plan the installation to use the fewest number of elbows and turns. When using  
elbows or making turns, allow as much room as possible. Bend vent gradually to  
avoid kinking. Avoid 90° turns.  
4"  
(10.2 cm)  
Box hood style  
4"  
(10.2 cm)  
2.5"  
(6.4 cm)  
2. Determine vent length.  
4"  
(10.2 cm)  
Angled style  
The maximum length of the exhaust system depends upon:  
Louvered style  
• The type of vent (rigid metal or flexible metal).  
• The number of elbows used.  
• Type of hood.  
See the exhaust vent length chart that matches your hood type for the maximum  
vent lengths you can use.  
3. Determine the number of elbows you will need.  
IMPORTANT: Do not use vent runs longer than specified in the Vent Length Chart.  
Vent Length Chart  
Number of  
90° turns  
or elbows  
Type of  
vent  
Box or  
Louvered  
hoods  
Angled  
hoods  
0
1
2
3
4
Rigid metal  
64 ft (20 m)  
58 ft (17.7 m)  
28 ft (8.5 m)  
Flexible metal 36 ft (11 m)  
Rigid metal  
Flexible metal  
54 ft (16.5 m)  
31 ft (9.4 m)  
48 ft (14.6 m)  
23 ft (7 m)  
In the column listing the type of metal vent you are using (rigid metal or flexible  
metal), find the maximum length of metal vent on the same line as the number of  
elbows.  
Rigid metal  
Flexible metal 27 ft (8.2 m)  
44 ft (13.4 m) 38 ft (11.6 m)  
19 ft (5.8 m)  
Rigid metal  
Flexible metal 25 ft (7.6 m)  
35 ft (10.7 m) 29 ft (8.8 m)  
17 ft (5.2 m)  
Rigid metal  
Flexible metal 23 ft (7 m)  
27 ft (8.2 m)  
21 ft (6.4 m)  
15 ft (4.6 m)  
Because Whirlpool Corporation policy includes a continuous commitment to improve  
our products, we reserve the right to change materials and specifications without notice.  
Dimensions are for planning purposes only. For complete details, see Installation  
Instructions packed with product. Specifications subject to change without notice.  
Ref. 8535888  
09-17-02  
 

Indesit Oven FI 21 KB GB User Manual
Ingersoll Rand Marine Radio 23644 400 User Manual
Ingersoll Rand Septic System 67200 XXX 3id User Manual
ION Camcorder Accessories 2 SD User Manual
John Deere Compact Loader 310SE User Manual
JVC Home Theater System TH M508 User Manual
Kenwood Stereo Amplifier KAC 6202 User Manual
KitchenAid Cooktop KECC507RSS05 User Manual
Klipsch Portable Speaker RC 7 User Manual
Kompernass Clock Radio KH 2190 User Manual