KitchenAid Dishwasher KUDD01DPPA User Manual

®
Undercounter Dishwasher  
PRODUCT MODEL SERIES  
OVERALL DIMENSIONS  
KUDD01DPPA  
23-7/16"  
(59.5 cm)  
22-7/16" *  
(57 cm)  
raised tabs for  
optional top  
attaching brackets  
Electrical: A 120-volt, 60 Hz, AC-only, 15-amp  
fused electrical supply is required. (Circuit breaker  
or time-delay fuse is recommended.) It is  
recommended that a separate circuit serving only  
this appliance be provided.  
32-3/16"- 34-1/2"  
(81.8 cm - 87.8 cm)  
30" ***  
(76.2 cm)  
The 3 prong grounded outlet must be installed  
within 6" (15.2 cm) to 18" (45.7 cm) of the cabinet  
side wall.  
If you plan to install a garbage disposer, an  
additional separate 120-volt, 60 Hz, AC-only,  
15- or 20-amp fused electrical supply is required.  
Water: A hot water line with 4.3-145 psi  
(30-1000 kPa) water pressure must be used.  
Water temperature must be minimum 120°F  
(49°C) at dishwasher. An easily accessible valve  
with 3/8" compression fitting must be installed in  
the hot water supply line.  
* If custom wood panels are to be used,  
the product depth is specified with an  
11/16" (18 mm) door panel thickness.  
side  
attaching  
tabs  
** Toe panel depth: Factory supplied,  
24-3/8" (5 – 11 cm); Custom wood,  
5" (12.7 cm) less the toe panel  
thickness for integrated. Minimum  
panel thickness using the supplied  
screws is 3/8" (9 mm).  
*** Door front height: Factory supplied –  
30" (76.2 cm); Custom wood – 28-1/4"  
(71.8 cm) minimum.  
2"– 4-3/8" **  
(5 cm – 11 cm)  
20-15/32"  
(52 cm)  
NOTE: Product shown with front panels  
for dimension purposes.  
drawer open  
CABINET OPENING DIMENSIONS  
*IMPORTANT: Custom wood door panels, if  
used, may be wider than the dishwasher to  
match surrounding cabinets. The 23-5/8"  
(60.0 cm) must be increased so that there is  
a 1/4" (6.4 mm) clearance between the  
cabinet side and panel edge.  
moisture protection tape  
4"  
(10 cm)  
For corner installation, there must be a 1/2"  
(12.7 mm) space between the adjacent  
cabinet doors (i.e. door knobs) and open  
dishwasher drawer.  
32-5/16"– 34-5/8"  
(82.0 cm – 88.0 cm)  
Utility hole:  
1-1/2" (3.8 cm) dia.  
hole, either side –  
immediately adjacent  
to corner.  
DRAIN OPTIONS  
Garbage disposal  
connection  
Sink drain waste  
tee connection  
22-7/8"  
(58.0 cm)  
drain hose  
support  
drain hose  
support  
23-5/8"* (60.0 cm)  
Air break connection  
air break  
drain hose  
connector  
6" (15.2 cm)  
minimum  
waste tee  
waste  
garbage  
disposal  
waste  
valve  
valve  
waste  
water supply  
27-1/2" – 32-1/4"  
(70 cm – 82 cm)  
water supply  
water supply  
8" (20.3 cm) min. bend  
radius from valve  
8" (20.3 cm) min. bend  
radius from valve  
Because Whirlpool Corporation policy includes a continuous commitment to improve our  
products, we reserve the right to change materials and specifications without notice.  
Dimensions are for planning purposes only. For complete details, see Installation  
Instructions packed with product. Specifications subject to change without notice.  
Ref. 8546448  
12-2-04  
 
®
KitchenAid Double Drawer Dishwasher Custom Door Panel Requirements  
MODELS: KUDD01DPPA  
Horizontal  
Position Line  
7) On the back side of the top drawer custom door panel,  
1 716”  
(36.5 mm)  
rout a 14” (6.4 mm) radius around the medallion cutout  
previously cut in step #4. The medallion end does not  
need to be routed.  
CUSTOM  
PANEL FOR  
TOP DRAWER  
(Back Side)  
8) On the back side of the bottom drawer custom door  
panel, rout a 14” (6.4 mm) radius around the medallion  
cutout previously cut in step #5. The medallion end does  
not need to be routed.  
Vertical  
Center Line  
Medallion  
Location Area  
9) If custom door panel material is not suitable to withstand  
damp conditions, seal with a moisture resistant material.  
For painted panels, paint all rear edges to improve sealing.  
FIGURE 3A  
10) On the backside of the top drawer custom door panel,  
measure and mark the vertical center line and horizontal  
position line (See figure 3A).  
Horizontal  
NOTE: The 1 716” (36.5 mm) horizontal position line is  
marked for later use in the installation process. Refer to  
the Installation Instructions Drawer Dishwasher included  
with the Drawer Dishwasher to align and attach the top  
drawer custom door panel to the factory supplied  
metal plate.  
Position Line  
1 316”  
(30.2 mm)  
CUSTOM  
PANEL FOR  
BOTTOM  
DRAWER  
(Back Side)  
11) On the backside of the bottom drawer custom door  
panel, measure and mark the vertical center line and  
horizontal position line (See figure 3B).  
Medallion  
Location Area  
Vertical  
Center Line  
NOTE: The 1 316” (30.2 mm) horizontal position line is  
marked for later use in the installation process. Refer to  
the Installation Instructions Drawer Dishwasher included  
with the Drawer Dishwasher to align and attach the  
bottom drawer custom door panel to the factory supplied  
metal plate.  
FIGURE 3B  
12) Mount the customer supplied handles to the locations  
previously marked on the top and bottom drawer  
custom panels.  
IMPORTANT: When mounting the customer supplied  
handles, screws must fit flush to the panel and not extend  
beyond the back surface.  
13) Refer to the Installation Instructions Drawer  
Dishwasher included with the Drawer Dishwasher  
to complete installation.  
 

Indesit Refrigerator BA 33 FNF User Manual
JBL Speaker PRX825W User Manual
JBL Speaker TLX271P User Manual
Jenn Air Cooktop CCG2421 User Manual
JL Audio Stereo Amplifier 505 User Manual
JVC Stereo System XL R910 User Manual
JVC VCR LPT0591 001A User Manual
Kambrook Fan KFH280 User Manual
Kenwood Car Stereo System KCA 20FM User Manual
Kenwood Mixer CHEF KM030 User Manual